RM新时代成立多久了,新时代RM|国际平台

23.1實驗內容

通過本實驗主要學習以下內容：

SDIO操作原理
SD卡讀寫實現

23.2實驗原理

SD卡是一種主要以Nand Flash作為存儲介質，具有體積小、數據傳輸速度快以及支持熱插拔的優點。如今，已被廣泛應用于數碼相機、便攜式移動設備以及手機等多種設備中。SD卡的驅動一般有SPI接口或SDIO接口，本例程介紹使用GD32F303的SDIO接口驅動SD卡的實現。

23.2.1SD卡基礎知識

SD卡:secure digital memory card是一種安全存儲器件。屬性是快閃存儲器（flash eeprom），功能用來存儲數據。

SD卡雖然是薄薄的一片，但是它并不是一個整體，而是由大量的集成電路組成。SD卡的內部結構如下圖所示，主要由信號端子，接口控制器和存儲區組成。

SD卡主要有兩種模式，SD模式和SPI模式。不同模式下，接口定義不同。下面是SD卡的引腳。

兩種模式的接口定義如下

SD模式中，主要由VCC(電源)，VSS(GND)，CLK（時鐘，由主控提供)，CMD(命令)，DAT0-3(數據輸入輸出)，由6線制組成進行通信。SPI模式，主要采用4線制通信，除了電源地外，由MISO，MOSI，CLK，CS組成。下面簡單介紹SD模式的操作。

要驅動SD卡工作，主要涉及兩個步驟。第一個步驟是SD卡的識別過程。第二個步驟是對SD卡進行讀寫過程，即主機控制器和SD卡之間進行數據傳輸?shù)倪^程。
要使SD卡能正常工作，一是要給SD卡供給穩定的電壓，二是要SD卡按用戶規定的方式工作。這兩項工作的實現，都是主機控制器通過給SD卡發送控制命令來實現的。
主機（SDIO控制器）要驅動SD卡工作，要使用許多的命令，包括應用層命令ACMD和通用命令CMD.主機（SDIO控制器）把命令發送給SD卡，SD卡會作出回應，這里的回應叫做響應，響應命令分為6類，分別是R1、R1b、R2、R3、R6、R7。主機（SDIO控制器）給SD卡發送命令之后，SD卡會作出響應，響應中包含主機（SDIO控制器）需要的數據，這些數據有SD的信息，容量，和存儲數據等等。上面已經提到了，SD卡工作，主要是識別和數據傳輸，它的識別過程有些復雜，寫代碼的時候，可以參考協議給的初始化流程圖。數據傳輸包括讀和寫，單字節和多字節讀寫。下兩節描述識別初始化流程圖和數據讀寫時序圖。

1、讀寫數據的時序圖

SDIO與SD卡通信一般以數據塊的形式進行傳輸，SDIO(多)數據塊讀操作，如下圖所示。

SDIO(多)數據塊寫操作，如下圖所示。

2、命令格式
SDIO所有的命令和響應都是在SDIO_CMD引腳上面?zhèn)鬏數模铋L度固定為48位，SDIO命令格式如下表所示。

3、寄存器
SDIO控制器的寄存器，主要設置SDIO控制器和命令的索引與參數。SD卡有5個寄存器CID,RCA,CSD,SCR.OCR。SD卡的信息從SD卡寄存器中獲取。

SD卡正常工作，就是根據SD卡初始化流程圖，發送命令，收到回復，直到流程結束。傳輸數據，也是根據讀寫時序圖，將要發送的數據放進命令中發送出去。

23.2.2SDIO模塊原理

SDIO為安全的數字輸入輸出接口，可以用于驅動SD卡、EMMC等，主要特征如下：

? MMC：與多媒體卡系統規格書V4.2及之前的版本全兼容。有三種不同的數據總線模式：1位(默認)、4位和8位；
? SD卡：與SD存儲卡規格版本2.0全兼容；
? SD I/O：與SD I/O卡規格版本2.0全兼容，有兩種不同的數據總線模式：1位(默認)和4位；
? CE-ATA：與CE-ATA數字協議版本1.1全兼容；
? 48MHz數據傳輸頻率和8位數據傳輸模式；
?中斷和DMA請求；
?完成信號使能和失能(CE-ATA)。

SDIO模塊結構框圖如下所示。主要包含兩大部分：SDIO適配器：由控制單元、命令單元和數據單元組成，控制單元管理時鐘信號，命令單元管理命令的傳輸，數據單元管理數據的傳輸；AHB接口：包括通過AHB總線訪問的寄存器、用于數據傳輸?shù)腇IFO單元以及產生中斷和DMA請求信號。

SDIO模塊可以實現對SD卡的完全驅動以及協議的實現，包括命令、響應等相關操作，本例程實現使用SDIO驅動SD卡初始化以及讀寫測試等相關操作，具體實現可以參考GD32F303用戶手冊以及代碼解析等。

23.3硬件設計

SD卡相關硬件電路如下圖所示，實驗板上具有SD卡卡座，信號線上有四根數據線，一根CMD命令線以及一根CLK時鐘線，所有信號線通過10K電阻進行上拉，電源地信號線具有10uf以及100nf電容，SD卡插入時，金屬接觸點朝下插入。

23.4代碼解析

23.4.1SDIO初始化配置函數

SDIO初始化配置在sd_io_init（）函數中，其中包括sd_init()初始化、sd_card_information_get（）SD卡信息獲取、sd_card_select_deselect（）SD卡選擇、sd_cardstatus_get（）SD卡狀態獲取、sd_bus_mode_config（）SD卡總線寬度配置以及sd_transfer_mode_config（）SD卡通信模式配置，歷程中選擇了4線查詢模式。

C
sd_error_enum sd_io_init(void)
{
sd_error_enum status = SD_OK;
uint32_t cardstate = 0;
status = sd_init();
if(SD_OK == status){
status = sd_card_information_get(&sd_cardinfo);
}
if(SD_OK == status){
status = sd_card_select_deselect(sd_cardinfo.card_rca);
}
status = sd_cardstatus_get(&cardstate);
if(cardstate & 0x02000000){
// printf("\r\n the card is locked!");
while (1){
}
}
if ((SD_OK == status) && (!(cardstate & 0x02000000)))
{
/* set bus mode */
status = sd_bus_mode_config(SDIO_BUSMODE_4BIT);
// status = sd_bus_mode_config( SDIO_BUSMODE_1BIT );
}
if (SD_OK == status)
{
/* set data transfer mode */
// status = sd_transfer_mode_config( SD_DMA_MODE );
status = sd_transfer_mode_config( SD_POLLING_MODE );
}
return status;
}

23.4.2獲取SD卡信息函數

獲取SD卡信息的函數如下所示，card_info_get（）。

C
void card_info_get(void)
{
uint8_t sd_spec, sd_spec3, sd_spec4, sd_security;
uint32_t block_count, block_size;
uint16_t temp_ccc;
//printf("\r\n Card information:");
sd_spec = (sd_scr[1] & 0x0F000000) >> 24;
sd_spec3 = (sd_scr[1] & 0x00008000) >> 15;
sd_spec4 = (sd_scr[1] & 0x00000400) >> 10;
if(2 == sd_spec)
{
if(1 == sd_spec3)
{
if(1 == sd_spec4)
{
// printf("\r\n## Card version 4.xx ##");
}
else
{
// printf("\r\n## Card version 3.0x ##");
}
}
else
{
// printf("\r\n## Card version 2.00 ##");
}
}
else if(1 == sd_spec)
{
// printf("\r\n## Card version 1.10 ##");
}
else if(0 == sd_spec)
{
// printf("\r\n## Card version 1.0x ##");
}

sd_security = (sd_scr[1] & 0x00700000) >> 20;
if(2 == sd_security)
{
// printf("\r\n## SDSC card ##");
}
else if(3 == sd_security)
{
// printf("\r\n## SDHC card ##");
}
else if(4 == sd_security)
{
// printf("\r\n## SDXC card ##");
}

block_count = (sd_cardinfo.card_csd.c_size + 1)*1024;
block_size = 512;
// printf("\r\n## Device size is %dKB ##", sd_card_capacity_get());
// printf("\r\n## Block size is %dB ##", block_size);
// printf("\r\n## Block count is %d ##", block_count);

if(sd_cardinfo.card_csd.read_bl_partial){
// printf("\r\n## Partial blocks for read allowed ##" );
}
if(sd_cardinfo.card_csd.write_bl_partial){
// printf("\r\n## Partial blocks for write allowed ##" );
}
temp_ccc = sd_cardinfo.card_csd.ccc;
//printf("\r\n## CardCommandClasses is: %x ##", temp_ccc);
if((SD_CCC_BLOCK_READ & temp_ccc) && (SD_CCC_BLOCK_WRITE & temp_ccc)){
// printf("\r\n## Block operation supported ##");
}
if(SD_CCC_ERASE & temp_ccc){
// printf("\r\n## Erase supported ##");
}
if(SD_CCC_WRITE_PROTECTION & temp_ccc){
// printf("\r\n## Write protection supported ##");
}
if(SD_CCC_LOCK_CARD & temp_ccc){
// printf("\r\n## Lock unlock supported ##");
}
if(SD_CCC_APPLICATION_SPECIFIC & temp_ccc){
// printf("\r\n## Application specific supported ##");
}
if(SD_CCC_IO_MODE & temp_ccc){
// printf("\r\n## I/O mode supported ##");
}
if(SD_CCC_SWITCH & temp_ccc){
// printf("\r\n## Switch function supported ##");
}
}

23.4.3SD卡數據塊寫入函數

SD卡數據塊寫入函數如下所示，通過該函數可實現SD卡數據塊的數據寫入。

C
sd_error_enum sd_block_write(uint32_t *pwritebuffer, uint32_t writeaddr, uint16_t blocksize)
{
/* initialize the variables */
sd_error_enum status = SD_OK;
uint8_t cardstate = 0;
uint32_t count = 0, align = 0, datablksize = SDIO_DATABLOCKSIZE_1BYTE, *ptempbuff = pwritebuffer;
uint32_t transbytes = 0, restwords = 0, response = 0;
__IO uint32_t timeout = 0;

if(NULL == pwritebuffer){
status = SD_PARAMETER_INVALID;
return status;
}

transerror = SD_OK;
transend = 0;
totalnumber_bytes = 0;
/* clear all DSM configuration */
sdio_data_config(0, 0, SDIO_DATABLOCKSIZE_1BYTE);
sdio_data_transfer_config(SDIO_TRANSMODE_BLOCK, SDIO_TRANSDIRECTION_TOCARD);
sdio_dsm_disable();
sdio_dma_disable();

/* check whether the card is locked */
if(sdio_response_get(SDIO_RESPONSE0) & SD_CARDSTATE_LOCKED){
status = SD_LOCK_UNLOCK_FAILED;
return status;
}

/* blocksize is fixed in 512B for SDHC card */
if(SDIO_HIGH_CAPACITY_SD_CARD == cardtype){
blocksize = 512;
writeaddr /= 512;
}

align = blocksize & (blocksize - 1);
if((blocksize > 0) && (blocksize <= 2048) && (0 == align)){
datablksize = sd_datablocksize_get(blocksize);
/* send CMD16(SET_BLOCKLEN) to set the block length */
sdio_command_response_config(SD_CMD_SET_BLOCKLEN, (uint32_t)blocksize, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();

/* check if some error occurs */
status = r1_error_check(SD_CMD_SET_BLOCKLEN);
if(SD_OK != status){
return status;
}
}else{
status = SD_PARAMETER_INVALID;
return status;
}

/* send CMD13(SEND_STATUS), addressed card sends its status registers */
sdio_command_response_config(SD_CMD_SEND_STATUS, (uint32_t)sd_rca << SD_RCA_SHIFT, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_SEND_STATUS);
if(SD_OK != status){
return status;
}

response = sdio_response_get(SDIO_RESPONSE0);
timeout = 100000;

while((0 == (response & SD_R1_READY_FOR_DATA)) && (timeout > 0)){
/* continue to send CMD13 to polling the state of card until buffer empty or timeout */
--timeout;
/* send CMD13(SEND_STATUS), addressed card sends its status registers */
sdio_command_response_config(SD_CMD_SEND_STATUS, (uint32_t)sd_rca << SD_RCA_SHIFT, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_SEND_STATUS);
if(SD_OK != status){
return status;
}
response = sdio_response_get(SDIO_RESPONSE0);
}
if(0 == timeout){
return SD_ERROR;
}

/* send CMD24(WRITE_BLOCK) to write a block */
sdio_command_response_config(SD_CMD_WRITE_BLOCK, writeaddr, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_WRITE_BLOCK);
if(SD_OK != status){
return status;
}

stopcondition = 0;
totalnumber_bytes = blocksize;

/* configure the SDIO data transmission */
sdio_data_config(SD_DATATIMEOUT, totalnumber_bytes, datablksize);
sdio_data_transfer_config(SDIO_TRANSMODE_BLOCK, SDIO_TRANSDIRECTION_TOCARD);
sdio_dsm_enable();

if(SD_POLLING_MODE == transmode){
/* polling mode */
while(!sdio_flag_get(SDIO_FLAG_DTCRCERR | SDIO_FLAG_DTTMOUT | SDIO_FLAG_TXURE | SDIO_FLAG_DTBLKEND | SDIO_FLAG_STBITE)){
if(RESET != sdio_flag_get(SDIO_FLAG_TFH)){
/* at least 8 words can be written into the FIFO */
if((totalnumber_bytes - transbytes) < SD_FIFOHALF_BYTES){
restwords = (totalnumber_bytes - transbytes)/4 + (((totalnumber_bytes - transbytes)%4 == 0) ? 0 : 1);
for(count = 0; count < restwords; count++){
sdio_data_write(*ptempbuff);
++ptempbuff;
transbytes += 4;
}
}else{
for(count = 0; count < SD_FIFOHALF_WORDS; count++){
sdio_data_write(*(ptempbuff + count));
}
/* 8 words(32 bytes) has been transferred */
ptempbuff += SD_FIFOHALF_WORDS;
transbytes += SD_FIFOHALF_BYTES;
}
}
}

/* whether some error occurs and return it */
if(RESET != sdio_flag_get(SDIO_FLAG_DTCRCERR)){
status = SD_DATA_CRC_ERROR;
sdio_flag_clear(SDIO_FLAG_DTCRCERR);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_DTTMOUT)){
status = SD_DATA_TIMEOUT;
sdio_flag_clear(SDIO_FLAG_DTTMOUT);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_TXURE)){
status = SD_TX_UNDERRUN_ERROR;
sdio_flag_clear(SDIO_FLAG_TXURE);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_STBITE)){
status = SD_START_BIT_ERROR;
sdio_flag_clear(SDIO_FLAG_STBITE);
return status;
}
}else if(SD_DMA_MODE == transmode){
/* DMA mode */
/* enable the SDIO corresponding interrupts and DMA */
sdio_interrupt_enable(SDIO_INT_DTCRCERR | SDIO_INT_DTTMOUT | SDIO_INT_TXURE | SDIO_INT_DTEND | SDIO_INT_STBITE);
dma_transfer_config(pwritebuffer, blocksize);
sdio_dma_enable();

timeout = 100000;
while((RESET == dma_flag_get(DMA1, DMA_CH3, DMA_FLAG_FTF)) && (timeout > 0)){
timeout--;
if(0 == timeout){
return SD_ERROR;
}
}
while ((0 == transend) && (SD_OK == transerror)){
}

if(SD_OK != transerror){
return transerror;
}
}else{
status = SD_PARAMETER_INVALID;
return status;
}

/* clear the SDIO_INTC flags */
sdio_flag_clear(SDIO_MASK_INTC_FLAGS);
/* get the card state and wait the card is out of programming and receiving state */
status = sd_card_state_get(&cardstate);
while((SD_OK == status) && ((SD_CARDSTATE_PROGRAMMING == cardstate) || (SD_CARDSTATE_RECEIVING == cardstate))){
status = sd_card_state_get(&cardstate);
}
return status;
}

23.4.4SD卡數據塊讀取函數

SD卡數據塊讀取函數如下所示。

C
sd_error_enum sd_block_read(uint32_t *preadbuffer, uint32_t readaddr, uint16_t blocksize)
{
/* initialize the variables */
sd_error_enum status = SD_OK;
uint32_t count = 0, align = 0, datablksize = SDIO_DATABLOCKSIZE_1BYTE, *ptempbuff = preadbuffer;
__IO uint32_t timeout = 0;

if(NULL == preadbuffer){
status = SD_PARAMETER_INVALID;
return status;
}

transerror = SD_OK;
transend = 0;
totalnumber_bytes = 0;
/* clear all DSM configuration */
sdio_data_config(0, 0, SDIO_DATABLOCKSIZE_1BYTE);
sdio_data_transfer_config(SDIO_TRANSMODE_BLOCK, SDIO_TRANSDIRECTION_TOCARD);
sdio_dsm_disable();
sdio_dma_disable();

/* check whether the card is locked */
if(sdio_response_get(SDIO_RESPONSE0) & SD_CARDSTATE_LOCKED){
status = SD_LOCK_UNLOCK_FAILED;
return status;
}

/* blocksize is fixed in 512B for SDHC card */
if(SDIO_HIGH_CAPACITY_SD_CARD == cardtype){
blocksize = 512;
readaddr /= 512;
}

align = blocksize & (blocksize - 1);
if((blocksize > 0) && (blocksize <= 2048) && (0 == align)){
datablksize = sd_datablocksize_get(blocksize);
/* send CMD16(SET_BLOCKLEN) to set the block length */
sdio_command_response_config(SD_CMD_SET_BLOCKLEN, (uint32_t)blocksize, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();

/* check if some error occurs */
status = r1_error_check(SD_CMD_SET_BLOCKLEN);
if(SD_OK != status){
return status;
}
}else{
status = SD_PARAMETER_INVALID;
return status;
}

stopcondition = 0;
totalnumber_bytes = blocksize;

/* configure SDIO data transmission */
sdio_data_config(SD_DATATIMEOUT, totalnumber_bytes, datablksize);
sdio_data_transfer_config(SDIO_TRANSMODE_BLOCK, SDIO_TRANSDIRECTION_TOSDIO);
sdio_dsm_enable();

/* send CMD17(READ_SINGLE_BLOCK) to read a block */
sdio_command_response_config(SD_CMD_READ_SINGLE_BLOCK, (uint32_t)readaddr, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_READ_SINGLE_BLOCK);
if(SD_OK != status){
return status;
}

if(SD_POLLING_MODE == transmode){
/* polling mode */
while(!sdio_flag_get(SDIO_FLAG_DTCRCERR | SDIO_FLAG_DTTMOUT | SDIO_FLAG_RXORE | SDIO_FLAG_DTBLKEND | SDIO_FLAG_STBITE)){
if(RESET != sdio_flag_get(SDIO_FLAG_RFH)){
/* at least 8 words can be read in the FIFO */
for(count = 0; count < SD_FIFOHALF_WORDS; count++){
*(ptempbuff + count) = sdio_data_read();
}
ptempbuff += SD_FIFOHALF_WORDS;
}
}

/* whether some error occurs and return it */
if(RESET != sdio_flag_get(SDIO_FLAG_DTCRCERR)){
status = SD_DATA_CRC_ERROR;
sdio_flag_clear(SDIO_FLAG_DTCRCERR);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_DTTMOUT)){
status = SD_DATA_TIMEOUT;
sdio_flag_clear(SDIO_FLAG_DTTMOUT);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_RXORE)){
status = SD_RX_OVERRUN_ERROR;
sdio_flag_clear(SDIO_FLAG_RXORE);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_STBITE)){
status = SD_START_BIT_ERROR;
sdio_flag_clear(SDIO_FLAG_STBITE);
return status;
}
while(RESET != sdio_flag_get(SDIO_FLAG_RXDTVAL)){
*ptempbuff = sdio_data_read();
++ptempbuff;
}
/* clear the SDIO_INTC flags */
sdio_flag_clear(SDIO_MASK_INTC_FLAGS);
}else if(SD_DMA_MODE == transmode){
/* DMA mode */
/* enable the SDIO corresponding interrupts and DMA function */
sdio_interrupt_enable(SDIO_INT_CCRCERR | SDIO_INT_DTTMOUT | SDIO_INT_RXORE | SDIO_INT_DTEND | SDIO_INT_STBITE);
sdio_dma_enable();
dma_receive_config(preadbuffer, blocksize);
timeout = 100000;
while((RESET == dma_flag_get(DMA1, DMA_CH3, DMA_FLAG_FTF)) && (timeout > 0)){
timeout--;
if(0 == timeout){
return SD_ERROR;
}
}
}else{
status = SD_PARAMETER_INVALID;
}
return status;
}

23.4.5SD卡lock和unlock配置函數

SD卡lock和unlock配置函數如下所示。通過形參實現對SD卡的lock和unlock，若希望lock SD卡，lcokstate配置為SD_LOCK；若希望unlock SD卡，lockstate配置為SD_UNLOCK.

C
sd_error_enum sd_lock_unlock(uint8_t lockstate)
{
sd_error_enum status = SD_OK;
uint8_t cardstate = 0, tempbyte = 0;
uint32_t pwd1 = 0, pwd2 = 0, response = 0;
__IO uint32_t timeout = 0;
uint16_t tempccc = 0;

/* get the card command classes from CSD */
tempbyte = (uint8_t)((sd_csd[1] & SD_MASK_24_31BITS) >> 24);
tempccc = (uint16_t)((uint16_t)tempbyte << 4);
tempbyte = (uint8_t)((sd_csd[1] & SD_MASK_16_23BITS) >> 16);
tempccc |= (uint16_t)((uint16_t)(tempbyte & 0xF0) >> 4);

if(0 == (tempccc & SD_CCC_LOCK_CARD)){
/* don't support the lock command */
status = SD_FUNCTION_UNSUPPORTED;
return status;
}
/* password pattern */
pwd1 = (0x01020600|lockstate);
pwd2 = 0x03040506;

/* clear all DSM configuration */
sdio_data_config(0, 0, SDIO_DATABLOCKSIZE_1BYTE);
sdio_data_transfer_config(SDIO_TRANSMODE_BLOCK, SDIO_TRANSDIRECTION_TOCARD);
sdio_dsm_disable();
sdio_dma_disable();

/* send CMD16(SET_BLOCKLEN) to set the block length */
sdio_command_response_config(SD_CMD_SET_BLOCKLEN, (uint32_t)8, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_SET_BLOCKLEN);
if(SD_OK != status){
return status;
}

/* send CMD13(SEND_STATUS), addressed card sends its status register */
sdio_command_response_config(SD_CMD_SEND_STATUS, (uint32_t)sd_rca << SD_RCA_SHIFT, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_SEND_STATUS);
if(SD_OK != status){
return status;
}

response = sdio_response_get(SDIO_RESPONSE0);
timeout = 100000;
while((0 == (response & SD_R1_READY_FOR_DATA)) && (timeout > 0)){
/* continue to send CMD13 to polling the state of card until buffer empty or timeout */
--timeout;
/* send CMD13(SEND_STATUS), addressed card sends its status registers */
sdio_command_response_config(SD_CMD_SEND_STATUS, (uint32_t)sd_rca << SD_RCA_SHIFT, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_SEND_STATUS);
if(SD_OK != status){
return status;
}
response = sdio_response_get(SDIO_RESPONSE0);
}
if(0 == timeout){
return SD_ERROR;
}

/* send CMD42(LOCK_UNLOCK) to set/reset the password or lock/unlock the card */
sdio_command_response_config(SD_CMD_LOCK_UNLOCK, (uint32_t)0x0, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_LOCK_UNLOCK);
if(SD_OK != status){
return status;
}

response = sdio_response_get(SDIO_RESPONSE0);

/* configure the SDIO data transmission */
sdio_data_config(SD_DATATIMEOUT, (uint32_t)8, SDIO_DATABLOCKSIZE_8BYTES);
sdio_data_transfer_config(SDIO_TRANSMODE_BLOCK, SDIO_TRANSDIRECTION_TOCARD);
sdio_dsm_enable();

/* write password pattern */
sdio_data_write(pwd1);
sdio_data_write(pwd2);

/* whether some error occurs and return it */
if(RESET != sdio_flag_get(SDIO_FLAG_DTCRCERR)){
status = SD_DATA_CRC_ERROR;
sdio_flag_clear(SDIO_FLAG_DTCRCERR);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_DTTMOUT)){
status = SD_DATA_TIMEOUT;
sdio_flag_clear(SDIO_FLAG_DTTMOUT);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_TXURE)){
status = SD_TX_UNDERRUN_ERROR;
sdio_flag_clear(SDIO_FLAG_TXURE);
return status;
}else if(RESET != sdio_flag_get(SDIO_FLAG_STBITE)){
status = SD_START_BIT_ERROR;
sdio_flag_clear(SDIO_FLAG_STBITE);
return status;
}

/* clear the SDIO_INTC flags */
sdio_flag_clear(SDIO_MASK_INTC_FLAGS);
/* get the card state and wait the card is out of programming and receiving state */
status = sd_card_state_get(&cardstate);
while((SD_OK == status) && ((SD_CARDSTATE_PROGRAMMING == cardstate) || (SD_CARDSTATE_RECEIVING == cardstate))){
status = sd_card_state_get(&cardstate);
}
return status;
}

23.4.6SD卡erase擦除操作函數

SD卡擦除操作函數如下，其形參為擦除起始地址以及結束地址。

C
sd_error_enum sd_erase(uint32_t startaddr, uint32_t endaddr)
{
/* initialize the variables */
sd_error_enum status = SD_OK;
uint32_t count = 0, clkdiv = 0;
__IO uint32_t delay = 0;
uint8_t cardstate = 0, tempbyte = 0;
uint16_t tempccc = 0;

/* get the card command classes from CSD */
tempbyte = (uint8_t)((sd_csd[1] & SD_MASK_24_31BITS) >> 24);
tempccc = (uint16_t)((uint16_t)tempbyte << 4);
tempbyte = (uint8_t)((sd_csd[1] & SD_MASK_16_23BITS) >> 16);
tempccc |= (uint16_t)((uint16_t)(tempbyte & 0xF0) >> 4);
if(0 == (tempccc & SD_CCC_ERASE)){
/* don't support the erase command */
status = SD_FUNCTION_UNSUPPORTED;
return status;
}
clkdiv = (SDIO_CLKCTL & SDIO_CLKCTL_DIV);
clkdiv += ((SDIO_CLKCTL & SDIO_CLKCTL_DIV8)>>31)*256;
clkdiv += 2;
delay = 120000 / clkdiv;

/* check whether the card is locked */
if (sdio_response_get(SDIO_RESPONSE0) & SD_CARDSTATE_LOCKED){
status = SD_LOCK_UNLOCK_FAILED;
return(status);
}

/* blocksize is fixed in 512B for SDHC card */
if (SDIO_HIGH_CAPACITY_SD_CARD == cardtype){
startaddr /= 512;
endaddr /= 512;
}

if((SDIO_STD_CAPACITY_SD_CARD_V1_1 == cardtype) || (SDIO_STD_CAPACITY_SD_CARD_V2_0 == cardtype) ||
(SDIO_HIGH_CAPACITY_SD_CARD == cardtype)){
/* send CMD32(ERASE_WR_BLK_START) to set the address of the first write block to be erased */
sdio_command_response_config(SD_CMD_ERASE_WR_BLK_START, startaddr, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_ERASE_WR_BLK_START);
if(SD_OK != status){
return status;
}

/* send CMD33(ERASE_WR_BLK_END) to set the address of the last write block of the continuous range to be erased */
sdio_command_response_config(SD_CMD_ERASE_WR_BLK_END, endaddr, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_ERASE_WR_BLK_END);
if(SD_OK != status){
return status;
}
}

/* send CMD38(ERASE) to set the address of the first write block to be erased */
sdio_command_response_config(SD_CMD_ERASE, (uint32_t)0x0, SDIO_RESPONSETYPE_SHORT);
sdio_wait_type_set(SDIO_WAITTYPE_NO);
sdio_csm_enable();
/* check if some error occurs */
status = r1_error_check(SD_CMD_ERASE);
if(SD_OK != status){
return status;
}
/* loop until the counter is reach to the calculated time */
for(count = 0; count < delay; count++){
}
/* get the card state and wait the card is out of programming and receiving state */
status = sd_card_state_get(&cardstate);
while((SD_OK == status) && ((SD_CARDSTATE_PROGRAMMING == cardstate) || (SD_CARDSTATE_RECEIVING == cardstate))){
status = sd_card_state_get(&cardstate);
}
return status;
}

23.4.7主函數

SD卡主函數如下，可實現對SD卡的擦寫讀以及加鎖解鎖操作。

C
int main(void)
{
sd_error_enum sd_error;
uint16_t i = 5;
#ifdef DATA_PRINT
uint8_t *pdata;
#endif /* DATA_PRINT */

/* configure the NVIC, USART and LED */
nvic_config();

bsp_uart_init(&BOARD_UART);

/* initialize the card */
do{
sd_error = sd_io_init();
}while((SD_OK != sd_error) && (--i));

if(i){
printf("\r\n Card init success!\r\n");
}else{
printf("\r\n Card init failed!\r\n");
while (1){
}
}

/* get the information of the card and print it out by USART */
card_info_get();

/* init the write buffer */
for(i=0; i<512; i++){
buf_write[i] = i;
}

printf("\r\n\r\n Card test:");

/* single block operation test */
sd_error = sd_block_write(buf_write, 100*512, 512);
if(SD_OK != sd_error){

printf("\r\n Block write fail!");
while (1){
}
}else{
printf("\r\n Block write success!");
}
sd_error = sd_block_read(buf_read, 100*512, 512);
if(SD_OK != sd_error){
printf("\r\n Block read fail!");

while (1){
}
}else{
//printf("\r\n Block read success!");
#ifdef DATA_PRINT
pdata = (uint8_t *)buf_read;
/* print data by USART */
printf("\r\n");
for(i = 0; i < 128; i++){
printf(" %3d %3d %3d %3d ", *pdata, *(pdata+1), *(pdata+2), *(pdata+3));
pdata += 4;
if(0 == (i + 1) % 4){
printf("\r\n");
}
}
#endif /* DATA_PRINT */
}

/* lock and unlock operation test */
if(SD_CCC_LOCK_CARD & sd_cardinfo.card_csd.ccc){
/* lock the card */
sd_error = sd_lock_unlock(SD_LOCK);
if(SD_OK != sd_error){
printf("\r\n Lock failed!");
while (1){
}
}else{
printf("\r\n The card is locked!");
}
sd_error = sd_erase(100*512, 101*512);
if(SD_OK != sd_error){
printf("\r\n Erase failed!");
}else{
__NOP();
printf("\r\n Erase success!");
}

/* unlock the card */
sd_error = sd_lock_unlock(SD_UNLOCK);
if(SD_OK != sd_error){
printf("\r\n Unlock failed!");
while (1){
}
}else{
printf("\r\n The card is unlocked!");
}
sd_error = sd_erase(100*512, 101*512);
if(SD_OK != sd_error){
printf("\r\n Erase failed!");
}else{
printf("\r\n Erase success!");
}

sd_error = sd_block_read(buf_read, 100*512, 512);
if(SD_OK != sd_error){
printf("\r\n Block read fail!");
while (1){
}
}else{
printf("\r\n Block read success!");
#ifdef DATA_PRINT
pdata = (uint8_t *)buf_read;
/* print data by USART */
printf("\r\n");
for(i = 0; i < 128; i++){
printf(" %3d %3d %3d %3d ", *pdata, *(pdata+1), *(pdata+2), *(pdata+3));
pdata += 4;
if(0 == (i + 1) % 4){
printf("\r\n");
}
}
#endif /* DATA_PRINT */
}
}

/* multiple blocks operation test */
sd_error = sd_multiblocks_write(buf_write, 200*512, 512, 3);
if(SD_OK != sd_error){
printf("\r\n Multiple block write fail!");
while (1){
}
}else{
printf("\r\n Multiple block write success!");
}
sd_error = sd_multiblocks_read(buf_read, 200*512, 512, 3);
if(SD_OK != sd_error){
printf("\r\n Multiple block read fail!");

while (1){
}
}else{
printf("\r\n Multiple block read success!");
#ifdef DATA_PRINT
pdata = (uint8_t *)buf_read;
/* print data by USART */
printf("\r\n");
for(i = 0; i < 512; i++){
printf(" %3d %3d %3d %3d ", *pdata, *(pdata+1), *(pdata+2), *(pdata+3));
pdata += 4;
if(0 == (i + 1) % 4){
printf("\r\n");
}
}
#endif /* DATA_PRINT */
}

while (1){
}
}

23.5實驗結果

將SD卡讀寫實驗例程燒錄到紅楓派開發板中，并在卡槽中插入SD卡，打開對應串口復位芯片，將會觀察到SD卡相關操作結果。

本教程由GD32 MCU方案商聚沃科技原創發布，了解更多GD32 MCU教程，關注聚沃科技官網

聲明：本文內容及配圖由入駐作者撰寫或者入駐合作網站授權轉載。文章觀點僅代表作者本人，不代表電子發燒友網立場。文章及其配圖僅供工程師學習之用，如有內容侵權或者其他違規問題，請聯系本站處理。舉報投訴

單片機

單片機

+關注

關注
6034

文章
44545

瀏覽量
634357
mcu

mcu

+關注

關注
146

文章
17108

瀏覽量
350885
SD卡

SD卡

+關注

關注
2

文章
562

瀏覽量
63870
開發板

開發板

+關注

關注
25

文章
5024

瀏覽量
97348

【GD32F470紫藤派開發板使用手冊】第十二講 SDIO-SD卡讀寫實驗

通過本實驗主要學習以下內容： ?SDIO操作原理 ?SD卡讀寫實現

發表于 05-18 09:36 ?1348次閱讀

【<b class='flag-5'>GD32F</b>470紫藤<b class='flag-5'>派</b><b class='flag-5'>開發板</b><b class='flag-5'>使用手冊</b>】第十二講 <b class='flag-5'>SDIO-SD</b><b class='flag-5'>卡</b><b class='flag-5'>讀寫實驗</b>

眾想科技-劉洋邊講邊寫STM32視頻教程 15.RS232串口通訊實驗

彩色液晶屏顯示漢字、英文、數字買板免費 第二十一講 SD存儲卡工作原理買板免費 第二十二講

發表于 10-12 11:16

【GD32F303】星空派介紹

一、開發板介紹星空派（GD）開發板是由旗點科技推出的一款GD32開發板，板載

發表于 09-11 17:55

【星空派GD32F303開發板試用體驗】開箱+環境搭建

本帖最后由 lustao 于 2021-10-19 09:29 編輯感謝發燒友學院以及廣州旗點智能科技有限公司為我和孩子提供此產品星空派GD32F303開發板。收到了星空派

發表于 10-18 14:15

【星空派GD32F303開發板試用體驗】開箱+環境搭建

https://bbs.elecfans.com/jishu_2179209_1_1.html感謝發燒友學院以及廣州旗點智能科技有限公司為我和孩子提供此產品星空派gd32F303開發板。收到了星空

發表于 11-02 15:36

【星空派GD32F303開發板試用體驗】+板卡概覽

本帖最后由 cooldog123pp 于 2021-11-6 21:07 編輯星空派（GD）開發板是由旗點科技推出的一款GD32開發板

發表于 11-06 21:05

【星空派GD32F303開發板試用體驗】文件讀寫與數碼相框的實現 （兼結題報告）

本帖最后由 jinglixixi 于 2021-11-27 01:23 編輯星空派開發板是旗點科技推出的一款以GD32F303ZET6為核心的開發板，該

發表于 11-26 12:05

星空派GD32F303開發板的相關資料下載

一、開發板介紹星空派（GD）開發板是由旗點科技推出的一款GD32開發板，板載

發表于 12-10 08:27

第二十三講 異步計數器

第二十三講 異步計數器概述一、計數器：用以統計輸入計數脈沖CP個數的電路。計數器的“?！保ㄓ肕表示）：二、計數器的分類1．按計數進制分2．按計數

發表于 03-30 16:27 ?1.2w次閱讀

模擬電路網絡課件 第二十三節:乙類雙電源互補對稱功率放大電路

模擬電路網絡課件 第二十三節:乙類雙電源互補對稱功率放大電路 5.2.1 電路的組成

發表于 09-17 08:56 ?2044次閱讀

2017中國西部微波射頻技術研討會暨第二十三屆國際電子測試測量研討會

2017中國西部微波射頻技術研討會暨第二十三屆國際電子測試測量研討會

發表于 07-05 15:12 ?1016次閱讀

【正點原子FPGA連載】第二十三章RGB-LCD字符和圖片顯示實驗 -摘自【正點原子】新起點之FPGA開發指南_V2.1

【正點原子FPGA連載】第二十三章RGB-LCD字符和圖片顯示實驗 -摘自【正點原子】新起點之FPGA開發指南_V2.1

發表于 11-24 14:36 ?13次下載

【GD32F303紅楓派開發板使用手冊】第二講 GPIO-流水燈實驗

GD32F303系列MCU最多可支持?112?個通用I/O?引腳(GPIO)，分別為?PA0 ~ PA15，?PB0 ~ PB15，?PC0 ~ PC15，PD0 ~ PD15，?PE0

發表于 05-29 10:02 ?1613次閱讀

【GD32H757Z海棠派開發板使用手冊】第十二講 SDIO-SD卡讀寫實驗

SD卡是一種主要以Nand Flash作為存儲介質，具有體積小、數據傳輸速度快以及支持熱插拔的優點。如今，已被廣泛應用于數碼相機、便攜式移動設備以及手機等多種設備中。SD卡的驅動一般有

發表于 06-05 10:35 ?678次閱讀

【GD32F303紅楓派開發板使用手冊】第二十講 SPI-SPI NAND FLASH讀寫實驗

通過本實驗主要學習以下內容： ?SPI通信協議，參考19.2.1東方紅開發板使用手冊 ?GD32F303 SPI操作方式，參考19.2.2東方紅開

發表于 06-20 09:50 ?871次閱讀